UC-CK Quick Start Guide (2024)

UniFi Cloud Key

Ethernet Cable

microSD Card (8 GB)

System Requirement

Web Browser: Google Chrome (Other browsers may have limited functionality.)

LED
White	Factory defaults.
Flashing White	Initializing.
Alternating White/Blue	Device is busy; do not touch or unplug it. This usually indicates that a process such as a firmware upgrade is taking place.
Blue	Device is working properly.
Shutdown Button
Press the Shutdown button to initiate a graceful shutdown (all services will be shut down and the CPU will remain active). After pressing the button, wait until the LED goes off, and then unplug the Cloud Key.
Ethernet Port
This Gigabit Ethernet port is used to connect the power and should be connected to the LAN and DHCP server. Power can be provided by an 802.3af PoE switch, such as the UniFi PoE Switch.
Reset Button
The Reset Button serves two functions: Restart Press and release the Reset button quickly. Restore to Factory Default Settings Press and hold the Reset button for more than five seconds.
USB Type C Power Port
Optional power source (5V, minimum 1A) if PoE is not available.
microSD Slot
This slot is used to back up the Cloud Key configuration to the microSD card (included).

Use an 802.3af-compliant switch, such as a UniFi Switch, or a USB power source (not included).

UniFi Switch

OR

USB Power Source

The UniFi Controller software is pre-installed on the UniFi Cloud Key. Use one of the following methods to launch the software:

• If you are using Chrome, go to the Chrome Instructions section (recommended).
• If you are using a different web browser, go to the Instructions for Other Web Browsers section.

Chrome Instructions

1. Ensure that your host system is on the same Layer-2 network as the UniFi Cloud Key.
2. Launch the Chrome web browser and type https://unifi.ui.com in the address field. Press enter (PC) or return (Mac).

   

3. Enter the username and password for your Ubiquiti account. Click Sign In.

   

4. Enable the Discover Cloud Key option at the top right.

   

5. If the Ubiquiti Device Discovery Tool is already installed, proceed to step 7.

   If the tool is not installed, you will be prompted to add it. Proceed to step 6.

6. To install the tool:
   1. Click Install.

      

      See Also

      Classes of IP addresses

   2. Click Add app to confirm.



7. The Ubiquiti Device Discovery Tool will search for the UniFi Cloud Key. Click Adopt in the Cloud Key’s Actions column to continue.

   

8. If the Cloud Key firmware is not the latest version, click Upgrade Firmware to upgrade the firmware.

   

9. Click Open Controller Wizard to set up the Controller on the Cloud Key.

   

10. The UniFi Setup Wizard screen appears. Follow the on-screen instructions. Then, click Finish to save your changes.

    	Note: For step-by-step instructions, refer to the User Guide, which is available at ui.com/download/unifi

    

11. Enter your ui.com account credentials and click Enable Cloud Access.

    

12. Go back to the UniFi Controller tab (https://unifi.ui.com) in your browser and wait for the UniFi Controller to be adopted.

    

13. Click Launch to open the UniFi Controller remotely.

The UniFi Controller management interface will appear. You can manage your UniFi devices and view network statistics using the UniFi Controller management interface.

For information on configuring and using the UniFi Controller software, refer to the User Guide located on our website: ui.com/download/unifi

Instructions for Other Web Browsers

1. Ensure that your host system is on the same Layer-2 network as the UniFi Cloud Key.
2. The UniFi Cloud Key is set to DHCP by default, so it will try to automatically obtain an IP address. Assign a specific IP address to the UniFi Cloud Key, or check the DHCP server for its IP address.

	Note: The default fallback IP address of the UniFi Cloud Key is 192.168.1.30.

3. Launch the web browser. In the address field, type https:// followed by the appropriate IP address. Press enter (PC) or return (Mac).

   

4. Click Manage to run the UniFi Setup Wizard.

   

	Note: You can click Configure to change the settings of the UniFi Cloud Key. The default login is ubnt/ubnt.

5. The UniFi Setup Wizard screen appears. Follow the on-screen instructions. Then, click Finish to save your changes.

	Note: For step-by-step instructions, refer to the User Guide, which is available at ui.com/download/unifi

After the UniFi Setup Wizard is finished, the UniFi Controller management interface will appear. Log in with the Admin Name and Password that you created, and then you can manage your UniFi devices and view network statistics using the UniFi Controller management interface.

For information on configuring and using the UniFi Controller software, refer to the User Guide.