Simple Ways to Measure Speaker Wattage: 14 Steps (with Pictures) (2024)

  • Categories
  • Computers and Electronics
  • Audio
  • Audio Speakers

Download Article

Explore this Article

methods

1Finding the Wattage Ratings for a Speaker

2Using an Amplifier Load Test to Test Compatibility

Other Sections

Video

Tips and Warnings

Things You'll Need

Related Articles

Expert Interview

References

Co-authored byAdam Parisand Eric McClure

Last Updated: August 7, 2023References

Download Article

Since speakers don’t produce power (that’s an amplifier’s job), speaker wattage refers to the power limit that a speaker can handle before it breaks or overheats.[1] This means that an amplifier’s wattage must fall within the acceptable wattage range for a speaker. You can multiply voltage by amperage to get wattage, so most of the information you need to determine a speaker’s wattage range should be printed on the speaker box, drum, or in the instruction manual. You can also perform a load test on an amplifier of an unknown wattage to see if it will work with a certain speaker.

Method 1

Method 1 of 2:

Finding the Wattage Ratings for a Speaker

Download Article

  1. 1

    Check the instruction manual to find the RMS. A speaker’s RMS refers to the continuous wattage that a speaker can handle for the ideal audio signal. When matching an amplifier to a speaker, match the amplifier’s wattage to the speaker’s RMS. The RMS is always listed in your speaker’s instruction manual.[2]

    • RMS stands for root mean square. It is a formula used to determine the efficiency of a current based on the wattage.
    • Without the manufacturer’s recommended wattage range, there is no test that you can use to find the RMS.
  2. 2

    Use the max wattage listed in the manual to find your wattage threshold. The maximum wattage refers the highest amount of power that a speaker can handle for a short period of time. If this number is exceeded by an amplifier, the speaker may break or catch fire. This number is usually printed alongside the RMS.[3]

    • If your speaker’s manual includes a peak wattage (or peak power), this measurement refers to the maximum amount of power that your speaker can receive for 1-2 seconds before shorting or dying. Think of it as the wattage that will instantly kill your speaker. A max wattage can be sustained for a short period of time.

    Warning: Do not perform a load test on a speaker by turning the volume up slowly while it’s connected to a high-powered amplifier. This is exceptionally dangerous and can result in a fire if you don’t know your speaker’s wattage limits.

    Advertisem*nt

  3. 3

    Look on the back of the speaker box if you don’t have a manual. If you don’t have your instruction manual, there should be a plate or sticker on your speaker listing the wattage, voltage, and amperage. Turn the speaker box around to find this information. Typically, it will list a range of numbers under wattage. This is an RMS range. Use this number to choose an appropriate amplifier for your speaker.[4]

    • These numbers are often printed directly on the drum of the speaker as well.
    • You can also enter your speaker’s brand and model into a search engine to find the specifications you need.
  4. 4

    Find the voltage and amperage numbers if the wattage isn’t mentioned. If you only have the speaker’s drum or there is no wattage information on the box, look for a number that ends in V, for voltage. Jot this number down on a piece of paper. Then, look for a number that ends in A. This is the amperage. Write this number down as well.[5]

    • Voltage is a measurement of an electrical current’s strength. Amperage refers to the volume of the current in a signal. The higher the current, the more electricity there is.
    • It helps to think of voltage and amperage in terms of a pipe. The amperage is the amount of water in a pipe, while the voltage is how much pressure there is the pipe. Think of the wattage as the size of the pipe. The higher the wattage is, the more voltage and amperage the speaker can handle.
  5. 5

    Multiply the amperage and the volts to find the max wattage. Take the speaker’s voltage and multiply it by the amperage to get a rough estimate of the maximum wattage. For example, if your speaker has 120V and 5A, multiply these numbers together to get 600 watts.[6]

    • To continue the pipe metaphor, multiplying the amount of water (the amperage) by how hard it is pushed out of the pipe (the amperage), tells you the minimum size of the pipe needed to handle the water and pressure. For the speaker, this essentially means that this is the maximum wattage, since the pipe shouldn’t get any smaller.
  6. Advertisem*nt

Method 2

Method 2 of 2:

Using an Amplifier Load Test to Test Compatibility

Download Article

  1. 1

    Look in the amplifier’s instruction manual to find the wattage first. A multimeter test is unnecessary if you have the amplifier’s instruction manual. Flip through the first 1-2 pages to find the amplifier’s specifications to find the wattage. If you don’t have this information, you’ll need to perform a load test by hooking the amplifier up to a speaker and testing the wattage through a sound test. If the amplifier’s maximum wattage does not exceed your speaker’s max wattage, they’re compatible[7]

    • The wattage information is often printed on the back of the amplifier as well. Look for a sticker or panel with tiny writing on it. The vast majority of amplifiers list the wattage here.
    • Testing the amplifier’s wattage involves playing an extremely loud and obnoxious sound, so it’s best to avoid performing the test if you can find the information elsewhere.
  2. 2

    Turn your multimeter off and plug the probes into the front. Don’t turn on your multimeter. Insert the red wire that came with your multimeter into the red slot on the front of the device. Take your black wire and plug it into the black slot next to it. For all intents and purposes, the red wire is your positive line and the black wire is your negative line.[8]

  3. 3

    Insert the multimeter’s probes into the speaker’s output jacks. Turn your amplifier off. On the back of the amplifier, find 2 unused output jacks for the amplifier. Slide the red multimeter probe into the red jack labelled positive (+). Slide the black probe into the black jack labelled negative (-). Plug a speaker into the other output slots if there isn’t one already plugged in.[9]

    • The probe refers to the thin length of metal at the end of each wire. These are the pieces that read the voltage.

    Tip: If you’re testing an amplifier with vertical screw slots on top for holding wires in place, insert each probe and use a hex wrench or screwdriver to tighten the screws and hold the probes still while you test.[10] If there is no vertical screw slot and the port is covered by a screw, hold the probe against the exterior of the screw while running your test.

  4. 4

    Set your multimeter to 200 volts (AC) and turn it on. Turn the dial on the front of your multimeter to 200 volts (AC). The AC voltage setting is represented by a V with a wavy line above it. The numbers next to this V are the AC voltage settings. Turn the dial to 200 and turn your multimeter on.[11]

    • For a low-powered amp, set the voltage to anywhere between 10-100.
  5. 5

    Wrap the clamp meter around the speaker wire in the positive jack. A clamp meter, or current clamp, is a digital meter with 2 jaws sticking out of the top. It reads the current (amperage) of any wire running through the opening in the middle of the jaws. Wrap your clamp meter’s jaws around the output wire that is connecting to your speaker’s positive terminal.[12]

    • Just to clarify, you are not clamping the wire directly. It simply needs to run through the opening in the middle of the jaws. Do not pinch the wire with your clamp meter.
    • If you speaker wire is color-coded, this positive output wire will be red. Otherwise, look for the wire connecting to the jack labelled positive (+).
  6. 6

    Play a 50 Hz test tone through your phone or a CD and turn it up. Turn the volume on the amplifier, speaker, or receiver all the way down. Plug a phone or mp3 player into the headphone jack on the front of your amplifier or speaker. Search online to find a 50 hertz (Hz) test tone. Press play on your phone or player to begin playing the test tone. Turn the test tone up as high as you can tolerate and let it continue playing.[13]

    • You cannot perform this test using music because the hertz value and power required to play a song shifts up and down as the sound gets louder and softer.
    • The 50 hertz test tones are pretty easy to find. They’re commonly used for this test specifically.
    • This part of the test is pretty loud and uncomfortable. Don’t do this late at night when people may be trying to go to sleep.
  7. 7

    Read the screens on your meter to find the amplifier’s voltage and amperage. With the sound playing, check the screen on your multimeter and write the number down. Then, check the number on the clamp meter and write this number down. The multimeter’s reading is your amplifier’s voltage, while the clamp meter’s reading is the amperage.[14]

    • As the test tone is playing, your multimeter is registering how much power the amplifier is putting on the current. The clamp meter is reading how much current there actually is.
  8. 8

    Multiply the voltage by the amperage to find the wattage. Turn the test tone off, shut your amplifier down, and remove your multimeter’s probes. Then, multiply your voltage and amperage together to find the amplifier’s wattage. For example, if your voltage was at 108V and the amperage was at 24A, your amplifier’s wattage is 2592 watts.[15]

    • If you didn’t play the test tone as loud as possible, you aren’t getting the maximum amperage. The real number is likely a little higher, but it’s not worth damaging your ears to find out.
  9. 9

    Compare the amp wattage to your speaker’s wattage. Use the speaker's wattage restrictions and RMS to determine if the speaker and amplifier can be hooked up together. If the amplifier's wattage exceeds the speaker's wattage, don't use them together.[16]

  10. Advertisem*nt

Expert Q&A

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

      Advertisem*nt

      Video

      Tips

      • For standalone speakers, like computer speakers, the amplifier is built into the speakers. You do not need to calculate the wattage of the amplifier to determine if the speaker is operating safely. The wattage listed on the box or on the speaker refers to both the RMS and the amplifier’s power.

        Thanks

        Helpful3Not Helpful2

      Submit a Tip

      All tip submissions are carefully reviewed before being published

      Name

      Please provide your name and last initial

      Submit

      Thanks for submitting a tip for review!

      Advertisem*nt

      Things You’ll Need

      Using an Amplifier Load Test to Test Compatibility

      • Multimeter
      • Clamp meter
      • Audio player

      You Might Also Like

      How toConnect Speakers to Your LaptopHow toInstall a Car Amp
      How toBridge an AmplifierHow to Connect a Bluetooth Speaker to a ComputerHow toMake Your Own Speakers3 Easy Ways to Clean Your iPhone Speakers without DamageHow toInstall Car SpeakersHow toBuild a Speaker BoxHow toMeasure Speaker ImpedanceHow toWire an Amp to a Sub and Head UnitHow toUse Banana PlugsHow toStop Amp HumHow toConnect Speakers to an AmpHow to Measure a Speaker Size

      Advertisem*nt

      Expert Interview

      Thanks for reading our article! If you’d like to learn more about fixing your tv, check out our in-depth interview with Adam Paris.

      More References (7)

      About This Article

      Simple Ways to Measure Speaker Wattage: 14 Steps (with Pictures) (35)

      Co-authored by:

      Adam Paris

      Audio & Visual Installation Expert

      This article was co-authored by Adam Paris and by wikiHow staff writer, Eric McClure. Adam Paris is an AV Expert and the Owner of Bat City TV in Austin, Texas. With over five years of professional experience, Adam specializes in installing audio and visual equipment such as TVs and sound systems. Adam received his degree from Austin Community College. This article has been viewed 133,764 times.

      How helpful is this?

      Co-authors: 5

      Updated: August 7, 2023

      Views:133,764

      Categories: Audio Speakers

      In other languages

      Spanish

      • Print
      • Send fan mail to authors

      Thanks to all authors for creating a page that has been read 133,764 times.

      Is this article up to date?

      Advertisem*nt

      Simple Ways to Measure Speaker Wattage: 14 Steps (with Pictures) (2024)
      Top Articles
      Slash Line | Glossary | MLB.com
      How can you prevent a brute force attack?
      Jack Doherty Lpsg
      WALB Locker Room Report Week 5 2024
      Bleak Faith: Forsaken – im Test (PS5)
      Repentance (2 Corinthians 7:10) – West Palm Beach church of Christ
      Missing 2023 Showtimes Near Cinemark West Springfield 15 And Xd
      Es.cvs.com/Otchs/Devoted
      What is international trade and explain its types?
      Nyuonsite
      T&G Pallet Liquidation
      Epaper Pudari
      FIX: Spacebar, Enter, or Backspace Not Working
      Full Range 10 Bar Selection Box
      Craigslist Pikeville Tn
      Binghamton Ny Cars Craigslist
      Meritas Health Patient Portal
      Spartanburg County Detention Facility - Annex I
      Craigslist Malone New York
      Transfer and Pay with Wells Fargo Online®
      Race Karts For Sale Near Me
      Healthier Homes | Coronavirus Protocol | Stanley Steemer - Stanley Steemer | The Steem Team
      Panic! At The Disco - Spotify Top Songs
      Filthy Rich Boys (Rich Boys Of Burberry Prep #1) - C.M. Stunich [PDF] | Online Book Share
      Helpers Needed At Once Bug Fables
      Inter Miami Vs Fc Dallas Total Sportek
      Wrights Camper & Auto Sales Llc
      Cor Triatriatum: Background, Pathophysiology, Epidemiology
      Wku Lpn To Rn
      Stephanie Bowe Downey Ca
      Sinfuldeed Leaked
      Craigs List Jax Fl
      Mosley Lane Candles
      UPC Code Lookup: Free UPC Code Lookup With Major Retailers
      Utexas Baseball Schedule 2023
      What Time Does Walmart Auto Center Open
      School Tool / School Tool Parent Portal
      Reborn Rich Ep 12 Eng Sub
      Mta Bus Forums
      Td Ameritrade Learning Center
      craigslist | michigan
      Cranston Sewer Tax
      18 terrible things that happened on Friday the 13th
      Panorama Charter Portal
      Danielle Ranslow Obituary
      Miami Vice turns 40: A look back at the iconic series
      House For Sale On Trulia
      Craigslist Sarasota Free Stuff
      Elvis Costello announces King Of America & Other Realms
      Cvs Minute Clinic Women's Services
      Jovan Pulitzer Telegram
      Latest Posts
      Article information

      Author: Edwin Metz

      Last Updated:

      Views: 6534

      Rating: 4.8 / 5 (78 voted)

      Reviews: 93% of readers found this page helpful

      Author information

      Name: Edwin Metz

      Birthday: 1997-04-16

      Address: 51593 Leanne Light, Kuphalmouth, DE 50012-5183

      Phone: +639107620957

      Job: Corporate Banking Technician

      Hobby: Reading, scrapbook, role-playing games, Fishing, Fishing, Scuba diving, Beekeeping

      Introduction: My name is Edwin Metz, I am a fair, energetic, helpful, brave, outstanding, nice, helpful person who loves writing and wants to share my knowledge and understanding with you.