- Categories
- Computers and Electronics
- Maintenance and Repair
Download Article
Step-by-step tutorial, disassembly to reassembly
Written byKyle Smith
Last Updated: September 27, 2023Fact Checked
Download Article
- Should you lube your switches? |
- Get Materials |
- Disassembly |
- Apply Lubricant |
- Reassembly |
- Tips
Is your mechanical keyboard a little too high-pitched? Is the tactile experience kind of rough? You’re in the right place. Lubricating your mechanical keyboard switches can make for a smoother, lower-pitched typing experience. This wikiHow guide will show you how to lubricate switches on your mechanical keyboard.
Things You Should Know
- Gather your materials. You’ll need: disposable gloves, keycap puller, switch puller, switch opener or flathead screwdriver, small brush, lubricant.
- Disassemble by pulling the keycap, pulling the switch, and opening the switch.
- Apply lubricant (lube) using your small brush.
Section 1 of 5:
Should you lube your switches?
Download Article
1
Maybe! Lubricating your mechanical keyboard can make your typing experience sound lower-pitched and feel smoother. You can enter Focus Mode (macOS), close your email tab, and listen to the calming clicks and clacks of your keyboard. Read the next steps to help you decide.[1]
- This guide will cover general information on how to lubricate tactile (brown) and linear (red) switches on a hot-swappable keyboard.[2]
2
Lubrication is great in these scenarios:
- Your keyboard has tactile or linear switches. These switches benefit the most from lubricant, since these are the type where you might want deeper sounds and less friction.
- The sound while typing is too high-pitched and you want lower, deeper-sounding shocks and clacks.
- Your mechanical keyboard typing experience seems too pingy or crunchy. Lubrication can reduce these qualities.
- Typing feels rough or scratchy as you press down the keys. Applying lube can help the keys slide past their component parts better.
Advertisem*nt
3
Lubrication is not great for:
- Clicky (blue) switches. Applying lube to this type of switch will reduce or completely get rid of their clicky feeling and sound.
- Optical switches. Lubricants may interfere with the optical sensing, depending on your model. If you decide to lube optical switches, look into how your keys function to avoid blocking the optical sensors.
Advertisem*nt
Section 2 of 5:
Get Materials
Download Article
1
Gather the necessary materials. You’ll need a few items to lubricate your switches.
- disposable gloves
- keycap puller
- switch puller
- switch opener
- This tool varies depending on your switch manufacturer.
- A small flathead screwdriver can work if you don’t have access to a dedicated switch opener.
- small brush
- lubricant (see the next step for more info)
- plastic bag (optional, for lubricating every spring at once)
- microfiber cloth (optional, to remove excess lubricant)
2
Choose your lubricant. There are several lubricants available specifically made for keyboard switches. While shopping for a lubricant, keep viscosity in mind.
- More viscosity is good for linear (red) switches, but can make tactile (brown) switches less tactile.
- Less viscosity is a great choice for reducing roughness without decreasing tactility too much.
- You can always go with a medium level viscosity if you’re not quite sure what to pick!
Advertisem*nt
Section 3 of 5:
Disassembly
Download Article
1
Pull the keycap. Use your keycap puller to remove a keycap from its switch.
- This section will cover an individual key. You can either do one key at a time, or do all of the keys at once.
- It’s also a great time to clean your mechanical keyboard.
2
Pull the switch. Use your switch puller to remove the switch from the keyboard.
- Reminder: This only works on hot-swappable keyboards. Soldered keyboards require that you disassemble the board and desolder each individual switch.
3
Open the switch. Switches are typically held together by clips. A lower and upper housing contain a stem and spring.[3]
- To use a switch opener, put the switch on the opener. Then press down to release the clips and open the switch.
- To use a flathead screwdriver, wedge the screwdriver under the clip to pry it up and detach the housing. Be careful not to break the clip.
- Note how the switch is assembled so you can reassemble it later. You can take a picture or video for reference later!
Advertisem*nt
Section 4 of 5:
Apply Lubricant
Download Article
1
Apply lubricant to the lower housing and stem. Use your small brush to dab lubricant onto the lower housing and stem. A small amount can make a big difference! You can always apply more later if you want an even smoother experience.
- Avoid uneven lumping of lube on the switch. This indicates you’ve added too much.
- Press the switch after reassembling it and reattaching it to the keyboard to assess whether you need to add more.
- The key areas for application are where the lower housing and stem make contact. This will reduce the friction between the two.
2
Apply lubricant to the spring. You can either:
- Use the brush to dab lubricant onto each spring.
- Or, if your springs are all the same, you can put lubricant and springs in a plastic bag. Then, shake the bag to coat the springs in lubricant.
Advertisem*nt
Section 5 of 5:
Reassembly
Download Article
Expert Q&A
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Advertisem*nt
Tips
See our guide on computer keyboard tips and tricks for more general information.
Thanks
Helpful0Not Helpful0
Submit a Tip
All tip submissions are carefully reviewed before being published
Name
Please provide your name and last initial
Submit
Thanks for submitting a tip for review!
Advertisem*nt
You Might Also Like
Advertisem*nt
References
About This Article
Written by:
Kyle Smith
wikiHow Technology Writer
This article was co-authored by wikiHow staff writer, Kyle Smith. Kyle Smith is a wikiHow Technology Writer, learning and sharing information about the latest technology. He has presented his research at multiple engineering conferences and is the writer and editor of hundreds of online electronics repair guides. Kyle received a BS in Industrial Engineering from Cal Poly, San Luis Obispo. This article has been viewed 7,590 times.
How helpful is this?
Co-authors: 5
Updated: September 27, 2023
Views:7,590
Categories: Maintenance and Repair
- Send fan mail to authors
Thanks to all authors for creating a page that has been read 7,590 times.
Is this article up to date?
Advertisem*nt